RSS-Feed abonnieren
PDF herunterladen
DOI: 10.1055/s-0039-1697808
Effects of Delayed Finishing/Polishing on Surface Roughness, Hardness and Gloss of Tooth-Coloured Restorative Materials
Publikationsverlauf
Publikationsdatum:
30. September 2019 (online)
ABSTRACT
Objectives: The aim of this study was to investigate the effect of delayed finishing/polishing on the surface roughness, hardness and gloss of tooth-coloured restorative materials.
Methods: Four different tooth-coloured restoratives: a flowable resin composite- Tetric Flow, a hybrid resin composite- Venus, a nanohybrid resin composite- Grandio, and a polyacid modified resin composite- Dyract Extra were used. 30 specimens were made for each material and randomly assigned into three groups. The first group was finished/polished immediately and the second group was finished/polished after 24 hours. The remaining 10 specimens served as control. The surface roughness of each sample was recorded using a laser profilometer. Gloss measurements were performed using a small-area glossmeter. Vickers microhardness measurements were performed from three locations on each specimen surface under 100g load and 10s dwell time. Data for surface roughness and hardness were analyzed by Kruskal Wallis test and data for gloss were subjected to one-way ANOVA and Tukey test (P<.05).
Results: The smoothest surfaces were obtained under Mylar strip for all materials. While there were no significant differences in surface roughness of immediate and delayed finished/polished Dyract Extra samples, immediately finished/polished Venus and Grandio samples showed significantly higher roughness than the delayed polished samples (P<.05). In Tetric Flow samples, immediately finishing/polishing provided smoother surface than delayed finishing/polishing (P<.05). The highest gloss values were recorded under Mylar strip for all materials. While delayed finishing/polishing resulted in a significantly higher gloss compared to immediate finishing/polishing in Venus samples (P<.05), no differences were observed between delayed or immediate finishing/polishing for the other materials (P>.05). The lowest hardness values were found under Mylar strip. Delayed finishing/polishing significantly increased the hardness of all materials.
Conclusions: The effect of delayed finishing/polishing on surface roughness, gloss and hardness appears to be material dependent. (Eur J Dent 2010;4:50-56)
-
References
- 1 Anusavice KJ, Antonson SA. Finishing and Polishing Materials in Philip’s Science of Dental Materials. 11th ed. Philadephia: WB Saunders Co.; 2003: 352-353
- 2 Morgan M. Finishing and polishing of direct posterior resin restorations. Prac Proced Aesth Dent 2004; 6: 211-217
- 3 Setcos JC, Tarim B, Suzuki S. Surface finish produced on resin composites by new polishing systems. Quintessence Int 1999; 30: 169-173
- 4 Bollen CM, Lambrechts P, Quirynen M. Comparison of surface roughness of oral hard materials to the threshold surface roughness for bacterial plaque retention: A review of the literature. Dent Mater 1997; 13: 258-269
- 5 Lu H, Roeder LB, Lei L, Powers JM. Effect of surface roughness on stain resistance of dental resin composites. J Esthet Restor Dent 2005; 17: 102-108
- 6 Reis A, Giannini M, Lovadino J, Ambrosano G. Effects of various finishing systems on the surface roughness and staining susceptibility of packable composite resins. Dent Mater 2003; 19: 12-18
- 7 Lai YL, Lin YC, Chang CS, Lee SY. Effects of sonic and ultrasonic scaling on the surface roughness of tooth-colored restorative materials for cervical lesions. Oper Dent 2007; 32: 273-278
- 8 O'Brien WJ, Johnston WM, Fanian F, Lambert S. The surface roughness and gloss of composites. J Dent Res 1984; 63: 685-688
- 9 Da Costa J, Ferracane J, Paravina RD, Mazur RF, Roeder L. The effect of different polishing systems on surface roughness and gloss of various resin composites. J Esthet Restor Dent 2007; 19: 214-226
- 10 Paravina RD, Roeder L, Lu H, Vogel K, Powers JM. Effect of finishing and polishing procedures on surface roughness, gloss and color of resin-based composites. Am J Dent 2004; 17: 262-266
- 11 Craig RG, Ward ML. Restorative Dental Materials. 10th ed. Mosby: St. Louis, USA; 1997
- 12 Rueggeberg FA, Craig RG. Correlation of parameters used to estimate monomer conversion in a light-cured composite. J Dent Res 1988; 67: 932-937
- 13 OʼBrien WJ. Physical Properties in Dental Materials and Their Selection. 4th ed. Illinois: Quintessence Publishing Co.; 2008. -18
- 14 Anusavice KJ. Physical Properties of Dental Materials in Philipʼs Science of Dental Materials. 10th ed. Philadephia: Saunders; 2003: 43
- 15 Ferracane JL, Mitchem JC, Condon JR, Todd R. Wear and marginal breakdown of composites with various degrees of cure. J Dent Res 1997; 76: 1508-1516
- 16 Stanford WB, Fan PL, Wozniak WT, Stanford JW. Effect of finishing on color and gloss of composites with different fillers. J Am Dent Assoc 1985; 110: 211-213
- 17 Inokoshi S, Burrow MF, Kataumi M, Yamada T, Takatsu T. Opacity and color changes of tooth-colored restorative materials. Oper Dent 1996; 21: 73-80
- 18 Turkun LS, Turkun M. The effect of one-step polishing system on the surface roughness of three esthetic resin composite materials. Oper Dent 2004; 29: 203-211
- 19 Irie M, Suzuki K. Effects of delayed polishing on gap formation of cervical restorations. Oper Dent 2002; 27: 59-65
- 20 Lopes GC, Franke M, Maia HP. Effect of finishing time and techniques on marginal sealing ability of two composite restorative materials. J Prosthet Dent 2002; 88: 32-36
- 21 Özgünaltay G, Yazici AR, Görücü J. Effect of finishing and polishing procedures on the surface roughness of new tooth-colored restoratives. J Oral Rehabil 2003; 30: 218-224
- 22 Baseren M. Surface roughness of nanofill and nanohybrid composite resin and ormocer-based tooth-colored restorative materials after several finishing and polishing procedures. J Biomater Appl 2004; 19: 121-133
- 23 Jung M, Sehr K, Klimek J. Surface texture of four nanofilled and one hybrid composite after finishing. Oper Dent 2007; 32: 45-52
- 24 Chung SM, Yap AUJ. Effects of surface finish on indentation modulus and hardness of dental composite restoratives. Dent Mater 2005; 21: 1008-1016
- 25 Venturini D, Cenci MS, Demarco FF, Camacho GB, Powers JM. Effect of polishing techniques and time on surface roughness, hardness and microleakage of resin composite restorations. Oper Dent 2006; 31: 11-17
- 26 Roberson TM, Heymann HO, Swift EJ. Sturdevantʼs Art and Science of Operative Dentistry. 4th edition. St. Louis: Mosby; 2000: 581
- 27 Hansen EK, Asmussen E. Effect of postponed polishing on marginal adaptation of resin used with dentin-bonding agent. Scand J Dent Res 1988; 96: 260-264
- 28 Jung M, Voit S, Klimek J. Surface geometry of three packable and one hybrid composite after finishing. Oper Dent 2003; 28: 53-59
- 29 Roeder LB, Tate WH, Powers JM. Effect of finishing and polishing procedures on the surface roughness of packable composites. Oper Dent 2000; 25: 534-543
- 30 Goncalves L, Filho JD, Guimarães JG, Poskus LT, Silva EM. Solubility, salivary sorption and degree of conversion of dimethacrylate-based polymeric matrixes. J Biomed Mater Res B Appl Biomater 2008; 85: 320-325
- 31 Silikas N, Kavvadia K, Eliades G, Watts D. Surface characterization of modern resin composites: A multitechnique approach. Am J Dent 2005; 18: 95-100
- 32 Uctasli MB, Arisu HD, Omürlü H, Eligüzeloglu E, Ozcan S, Ergun G. The effect of different finishing and polishing systems on the surface roughness of different composite restorative materials. J Contemp Dent Pract 2007; 8: 89-96
- 33 Scheibe KG, Almeida KG, Medeiros IS, Costa JF, Alves CM. Effect of different polishing systems on the surface roughness of microhybrid composites. J Appl Oral Sci 2009; 17: 21-26
- 34 Yap AU, Sau CW, Lye KW. Effects of finishing/polishing time on surface characteristics of tooth-coloured restoratives. J Oral Rehabil 1998; 25: 456-461
- 35 Cenci MS, Venturini D, Pereira-Cenci T, Piva E, Demarco FF. The effect of polishing techniques and time on the surface characteristics and sealing ability of resin composite restorations after one-year storage. Oper Dent 2008; 33: 169-176
- 36 Lee YK, Lu H, Oguri M, Powers JM. Changes in gloss after simulated generalized wear of composite resins. J Prosthet Dent 2005; 94: 370-376
- 37 Heintze SD, Forjanic M, Rousson V. Surface roughness and gloss of dental materials as a function of force and polishing time in vitro. Dent Mater 2006; 22: 146-165
- 38 Joniot SB, Gregoire GL, Auther AM, Roques YM. Threedimensional optical profilometry analysis of surface states obtained after finishing sequences for three composite resins. Oper Dent 2000; 25: 311-315